FemtoScan Wiki

[[en:processing:выравнивание]]

Trace:

Login

You are currently not logged in! Enter your authentication credentials below to log in. You need to have cookies enabled to log in.

Login

Forgotten your password? Get a new one: Set new password

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
en:processing:выравнивание [2012/03/07 14:26]
Анна Протопопова created
en:processing:выравнивание [2012/03/14 15:19] (current)
Line 3: Line 3:
 Often images obtained by AFM have the common slope or the common salience. Such distortions can appear for different reasons. As a rule, they are related to the temperature drift and the non-linearity of the piezoceramic manipulator. This macroscopic surface pattern usually prevents definition of the object’s structure. Often images obtained by AFM have the common slope or the common salience. Such distortions can appear for different reasons. As a rule, they are related to the temperature drift and the non-linearity of the piezoceramic manipulator. This macroscopic surface pattern usually prevents definition of the object’s structure.
  
-{{:​processing:​linear_fit_1.jpg|}}+{{:en:​processing:​linear_fit_1_en.jpg|}}
  
-Чтобы избавиться от него, из исходной матрицы значений вычитают поверхность первого или второго порядка ​(плоскостьпараболу или гиперболу). Выравнивание осуществляется по команде ​**Выравнивание** в [[processing:меню_математика|меню Математика]] или нажатием на кнопку+To get rid of it you need to subtract the surface of the first or the second order (planeparabola, or hyperbolafrom the initial value matrixAligning is performed by using the **Fitting** command from the  ​[[меню_математика|Mathematics menu]] or by clicking on the button
  
-{{:​processing:​linear_fit.jpg|}}+{{:en:​processing:​linear_fit_en.jpg|}}
  
-При выполнении этой команды появляется окно параметровв котором можно указать тип вычитаемой поверхности: **Линейная** - для вычитания общего наклона ​(плоскостиили ​**Параболическая** - для вычитания поверхности второго порядка:+When using this commanda parameter box appears where you can indicate the type of the surface to be subtracted: **Linear** -– for subtraction of the common slope (planeor **Parabolic** -– for subtraction of the surface of the second order:
  
-{{:​processing:​linear_fit_2.jpg|}} ​     {{:​processing:​linear_fit_3.jpg|}}+{{:en:​processing:​linear_fit_2_en.jpg|}} ​     {{:en:​processing:​linear_fit_3_en.jpg|}}
  
-Если исходный файл содержит несколько изображенийто обрабатывать их можно одинаковым образом,​ вычитая одну и ту же поверхность,​ или независимо друг от другаСпособ обработки определяется параметром ​**Обработка под-изображений**: +If the initial file contains several imagesthey can be processed in the same way by subtracting the same surface or independently of each otherThe processing method is defined by the **Subimage processing** parameter
-  - **Раздельно** - для каждого содержащегося в файле изображения высчитывается средняя поверхностьопределенная методом наименьших квадратов для конкретного изображения+  - **Separate** - for every image that the file containsthe average surface defined by the smallest square method for the specific image is calculated
-  - **По активному** - поверхность рассчитывается для активного изображения,​ а вычитается из всех+  - **Use active** - the surface is calculated for the active image and is subtracted from all the images
-  - **По всем** - рассчитываются средние поверхности по всем подызображениям и усредняются.+  - **Use all** - average surfaces for all the sub-images are calculated and averaged.
  
-Если напротив поля ​**Удалять постоянную составляющую** стоит галочкато общее смещение всей поверхности относительно нуля удаляется.+If a check mark is placed against the **Remove constant offset** fieldthe common offset of the entire surface relative to zero is removed.
  
-Необходимо помнить,​ что если перед тем, как вызвать команду ​**Выравнивание**, Вы выделите небольшой фрагмент изображениято при вычислении уравнения поверхности будут использоваться только значения точек, попавших в выделениеПри этом, построенная поверхность будет вычтена из всего изображения.+It is necessary to remember that if you select a small fragment of the image before you call up the **Fitting** commandduring the calculation of the surface equationonly values of the selected points will be usedThe formed surface will be subtracted from the entire image.
  
-Аналогичным образом можно вычесть поверхность,​ построенную по МНК по нескольким точкам,​ отмеченным ​[[processing:метки|метками]] на изображении.+The surface formed using SSM based on several points ​[[метки|marked]] in the image can be subtracted in a similar way.